Home › Guides › VW Crafter radio code: how to find and enter it

VW Crafter radio code: how to find and enter it

Updated · 3 min read

Crafter vans often get new batteries or jump starts on site, and the factory radio locks itself each time the power is cut. On the first-generation Crafter it needs its 4-digit code to work again.

Which radio does your Crafter have?

ModelYearsFactory radiosCode?
Crafter Mk12006–2017RCD 200, RCD 210, RCD 300, RCD 310, RNS 310, RNS 510Yes, 4-digit code
Crafter Mk22017 onwardsComposition / Discover touchscreens (MIB)No 4-digit code

Most Crafter vans had a basic RCD radio; the RNS sat navs were less common. Exact fitment varies by year and trim.

If your car has a touchscreen that says "Component Protection" rather than SAFE, it's a MIB unit with no 4-digit code. See why MIB radios have no code.

Step 1: find the serial

The code is tied to the radio's serial number, printed on a label on the radio's casing. It's 14 characters and starts with VWZ, for example VWZ1Z2A1234567. Don't use the part number, which starts with digits.

Crafter radios come out with VW radio release keys. The dash is high and deep, so pull the radio out slowly and straight. The label is on the top or side of the casing. More detail: where to find your radio serial number.

Step 2: get the code

First check the service book wallet for a radio code card whose serial matches your radio. If there isn't one, you can order the code from the serial: £19.99, delivered by email in 1–3 hours on average.

Need your Crafter radio code? Original 4-digit code from your VWZ serial: £19.99, 1–3 hours on average, money-back guarantee.

Get my code

Step 3: enter the code

  1. Switch the ignition on and the radio on. The display shows SAFE, then usually 1000 or 0000.
  2. Set each digit with preset buttons 1–4. Button 1 changes the first digit, button 2 the second, and so on. Each press counts up by one, and 9 wraps round to 0. If the display starts at 1000, the first digit already shows 1.
  3. Confirm by holding the accept button for 2–3 seconds until the radio plays. This is usually OK, SCAN or the right seek arrow.

Touchscreen units (RCD 510, RNS 310, RNS 315 and RNS 510) show an on-screen keypad instead: tap the four digits and press OK.

Guides for the radios fitted to the Crafter: RCD 310 · RCD 200, RCD 210 and RCD 300 · RNS 310 / RNS 315 · RNS 510. Our Workshop Manual has a press-count planner that tells you exactly how many presses each button needs.

Two wrong entries usually lock the radio into SAFE 2 for 60 minutes. If that happens, leave the ignition and radio on for an unbroken hour, then enter the correct code once. See how the SAFE 2 lockout works.

For van hire and fleet operators

If you run several Crafters, collect the serials when the vans are in for servicing so you can order every code at once. Our trade page gives 10% off 3 or more radios and 15% off 10 or more, paid on one invoice.

Quick answers

Does the new Crafter need a radio code?

No. Crafters from 2017 use MIB touchscreen systems with Component Protection, which don't use a 4-digit code.

Where is the serial number on a VW Crafter radio?

On a label on the radio casing: 14 characters starting VWZ. Slide the radio out with release keys to read it.

How much is a VW Crafter radio code?

£19.99 from RadioUnlock, delivered by email in 1–3 hours on average. Trade discounts are available for 3 or more radios.